20 the taz part has fully molded, compliant leadframe construction designed for use in applications utilizing solder (reflow, wave or vapor phase), conductive adhesive or thermal compression bonding techniques. each chip is marked with polarity, capaci- tance code and rated voltage. the series comprises eight case sizes (see dimensional chart below) with the new v case enabling capacitance values to 470 f. the c case, with its non-stan- dard aspect ratio, is retained as a qpl (qualified product list) only special. s l a h w 1 w marking (white marking on black body) case sizes a through e share a common (0.050" nom) height profile, compatible with pcmcia type ii applications. these allow downsizing in all portable applications, ranging from sub-miniature hard-disc drive (hdd)/computer to portable communications/gps systems. the f case at 0.070" nom offers the versatility of a low profile design, while allowing capacitance ratings to 100 f for low voltage filtering applications. cases g, h and v also offer lower profile and greater volumetric efficiency than their nearest eia sized counterparts (ref. cwr11). these are especially suited to power supply applications. the v case is a new addition to the series designed to maximize capacitance/voltage ratings while achieving minimum esr levels and maximum power dissipation. the regular configuration allows for banking (brickwalling) applications where maximum capacitance with minimal esr and inductance are required in a limited board space. polarity stripe (+) capacitance code rated voltage taz series including cwr09 and cots-plus case dimensions: millimeters (inches) case length l width w height h term. width w 1 term. length a s min code 0.38 (0.015) 0.38 (0.015) 0.38 (0.015) .13 (.005) a 2.54 (0.100) 1.27 (0.050) 1.27 (0.050) 1.270.13 0.76 (0.030) 0.38 (0.015) (0.050.005) b 3.81 (0.150) 1.27 (0.050) 1.27 (0.050) 1.270.13 0.76 (0.030) 1.65 (0.065) (0.050.005) d 3.81 (0.150) 2.54 (0.100) 1.27 (0.050) 2.41+0.13/-0.25 0.76 (0.030) 1.65 (0.065) (0.095+0.005/-0.01) e 5.08 (0.200) 2.54 (0.100) 1.27 (0.050) 2.41+0.13/-0.25 0.76 (0.030) 2.92 (0.115) (0.095+0.005/-0.01) f 5.59 (0.220) 2.54 (0.100) 1.78 (0.070) 3.300.13 0.76 (0.030) 3.43 (0.135) (0.130.005) g 6.73 (0.265) 2.79 (0.110) 2.79 (0.110) 2.670.13 1.27 (0.050) 3.56 (0.140) (0.1050.005) h 7.24 (0.285) 3.81 (0.150) 2.79 (0.110) 3.68+0.13/-0.51 1.27 (0.050) 4.06 (0.160) (0.145+0.005/-0.02) v 6.93 (0.273) 5.97 (0.235) 3.45 (0.136) 3.050.13 1.4 (0.055) 3.38 (0.133) (0.1200.005)
21 taz series including cwr09 and cots-plus cwr09 j b 225 k b a \tr technical data: unless otherwise specified, all technical data relate to an ambient temperature of 25c capacitance range: 0.1 to 470 f capacitance tolerance: 20%, 10%, 5% rated dc voltage: (v r ) # 85c: 4 6 10 15 20 25 35 50 category voltage: (v c ) 125c: 2.7 4 7 10 13 17 23 33 surge voltage: (v c ) # 85c: 5.2 8 13 20 26 33 46 65 125c: 3.5 5 9 12 16 21 28 40 operating temperature range: -55c to +125c fully qualified to mil-prf-55365/4, this series represents the most flexible of surface mount form factors, offering eight case sizes (a through h). this series is fully interchangeable with cwr06 conformal types, while offering the advantages of molded body/compliant termination construction, polarity, capacitance and jan brand packaging. the molded con- struction is compatible with a wide range of smt board assembly processes including wave or reflow solder, con- ductive epoxy or compression bonding techniques. the five smaller cases are characterized by their low profile construc- tion, with the a case being the worlds smallest molded mil- itary tantalum. there are three termination finishes available: fused solder plated (k per mil-prf-55365), hot solder dipped (c) and gold plated (b). in addition, the molding compound has been selected to meet the requirements of ul94v-0 and outgassing requirements of nasa sp-r- 0022a. cwr09 - mil-prf-55365/4 part numbering system taz cots-plus series style voltage code termination finish capacitance code packaging surge test option reliability grade capacitance tolerance taz h 227 m 006 c r sb 08 00 part numbering system style case size capacitance code capacitance tolerance voltage code surge test option termination finish qualification/ reliability packaging standard or low esr range this series features: ? cwr09 form factor in standard and extended ratings. ? low profile molded design (cases a through e). ? low esr ratings (cases g through v). ? extended case size (v) for ratings to 470 f. ? weibull reliability grading and surge test options. all ratings in this series offer the advantages of molded body/compliant termination construction, polarity, capaci- tance and voltage marking. the molded construction is compatible with a wide range of smt board assembly processes including wave or reflow solder, conductive epoxy or compression bonding techniques.
22 surface mount military cwr09 - mil-prf-55365/4 and taz cots-plus dc leakage (max) dissipation factor (max) qpl part number dc rated cap esr (max) case avx part number (for reference only) voltage (nom) +25c +85c +125c +25c +85/125c -55c 100 khz size (85c) f (a) (a) (a) (%) (%) (%) +25c (volts) (ohms) taza225*004c h #@0^++ cwr09c^225*@+ h 4 2.2 1.0 10 12 6 8 8 8.0 a taza475*004c h #@0^++ 4 4.7 1.0 10 12 6 8 8 12.0 a tazb475*004c h #@0^++ cwr09c^475*@+ h 4 4.7 1.0 10 12 6 8 8 8.0 b tazb106*004c h #@0^++ 4 10.0 1.0 10 12 8 10 10 8.0 b tazd106*004c h #@0^++ cwr09c^106*@+ h 4 10.0 1.0 10 12 8 8 10 4.0 d taze156*004c h #@0^++ cwr09c^156*@+ h 4 15.0 1.0 10 12 8 10 12 3.5 e tazd226*004c h #@0^++ 4 22.0 1.0 10 12 8 10 12 4.0 d taze336*004c h #@0^++ 4 33.0 2.0 20 24 8 10 12 3.0 e tazf336*004c h #@0^++ cwr09c^336*@+ h 4 33.0 2.0 20 24 8 10 12 2.2 f tazg686*004c h #@0^++ cwr09c^686*@+ h 4 68.0 3.0 30 36 10 12 12 1.1 g tazf107*004c h #@0^++ 4 100.0 4.0 40 48 10 12 12 2.0 f tazh107*004c h #@0^++ cwr09c^156*@+ h 4 100.0 4.0 40 48 10 12 12 0.9 h tazg157*004c h #@0^++ 4 150.0 6.0 60 72 10 12 12 1.0 g taza155*006c h #@0^++ cwr09d^155*@+ h 6 1.5 1.0 10 12 6 8 8 8.0 a taza335*006c h #@0^++ 6 3.3 1.0 10 12 6 8 8 12.0 a tazb335*006c h #@0^++ cwr09d^335*@+ h 6 3.3 1.0 10 12 6 8 8 8.0 b tazb685*006c h #@0^++ 6 6.8 1.0 10 12 6 8 8 8.0 b tazd685*006c h #@0^++ cwr09d^685*@+ h 6 6.8 1.0 10 12 6 8 8 4.5 d taze106*006c h #@0^++ cwr09d^106*@+ h 6 10.0 1.0 10 12 8 10 12 3.5 e tazd156*006c h #@0^++ 6 15.0 1.0 10 12 8 10 12 5.0 d taze226*006c h #@0^++ 6 22.0 2.0 20 24 8 10 12 3.5 e tazf226*006c h #@0^++ cwr09d^226*@+ h 6 22.0 2.0 20 24 8 10 12 2.2 f tazg476*006c h #@0^++ cwr09d^476*@+ h 6 47.0 3.0 30 36 10 12 12 1.1 g tazf686*006c h #@0^++ 6 68.0 4.0 40 48 10 12 12 1.5 f tazh686*006c h #@0^++ cwr09d^686*@+ h 6 68.0 4.0 40 48 10 12 12 0.9 h tazg107*006c h #@0^++ 6 100.0 6.0 60 72 10 12 12 1.1 g tazg107*006l h #@0^++ 6 100.0 6.0 60 72 10 12 12 0.150 g tazh227*006c h #@0^++ 6 220.0 10.0 100 120 10 12 12 0.9 h tazh227*006l h #@0^++ 6 220.0 10.0 100 120 10 12 12 0.100 h tazv477*006l h #@0^++ 6 470.0 28.0 280 336 12 14 14 0.055 v part number designations ^ = termination finish: 1 # = inspection level: * = tolerance: @ = failure rate level: + = surge option: h = packaging: for taz p/n: s = std. conformance m = 20% weibull: b = 0.1%/1000 hrs. for taz p/n: for taz p/n: 9 = gold plated l = optional group a k = 10% (90% c = 0.01%/1000 hrs. 00 = none b = bulk 8 = hot solder dipped for cwr p/n: j = 5% (special conf.) 23 = 10 cycles, +25c r = 7" t&r 0 = solder fused m = military order only) comm: z = non er 24 = 10 cycles, s = 13" t&r for cwr p/n: conformance per -55c & +85c for cwr p/n: b = gold plated mil-prf-55365 for cwr p/n: bulk = standard c = hot solder dipped a = 10 cycles, +25c \tr = 7" t&r k = solder fused b = 10 cycles, \tr13 = 13" t&r -55c & +85c \w = waffle following the voltage code, c designates standard, l designates low esr ratings (1) v case size is only available as solder fused
23 dc leakage (max) dissipation factor (max) qpl part number dc rated cap esr (max) case avx part number (for reference only) voltage (nom) +25c +85c +125c +25c +85/125c -55c 100 khz size (85c) f (a) (a) (a) (%) (%) (%) +25c (volts) (ohms) taza105*010c h #@0^++ cwr09f^105*@+ h 10 1.0 1.0 10 12 6 8 8 10.0 a taza225*010c h #@0^++ 10 2.2 1.0 10 12 6 8 8 12.0 a tazb225*010c h #@0^++ cwr09f^225*@+ h 10 2.2 1.0 10 12 6 8 8 8.0 b tazb475*010c h #@0^++ 10 4.7 1.0 10 12 6 8 8 8.0 b tazd475*010c h #@0^++ cwr09f^475*@+ h 10 4.7 1.0 10 12 6 8 8 4.5 d tazd685*010c h #@0^++ 10 6.8 1.0 10 12 6 8 8 5.0 d taze685*010c h #@0^++ cwr09f^685*@+ h 10 6.8 1.0 10 12 6 8 8 3.5 e tazd106*010c h #@0^++ 10 10.0 1.0 10 12 6 8 8 4.0 d taze156*010c h #@0^++ 10 15.0 2.0 20 24 8 10 10 3.0 e tazf156*010c h #@0^++ cwr09f^156*@+ h 10 15.0 2.0 20 24 8 8 10 2.5 f taze226*010c h #@0^++ 10 22.0 3.0 30 36 8 10 10 2.0 e tazg336*010c h #@0^++ cwr09f^336*@+ h 10 33.0 3.0 30 36 10 12 12 1.1 g tazf476*010c h #@0^++ 10 47.0 4.0 40 48 10 12 12 1.5 f tazh476*010c h #@0^++ cwr09f^476*@+ h 10 47.0 5.0 50 60 10 12 12 0.9 h tazg686*010c h #@0^++ 10 68.0 6.0 60 72 10 12 12 1.1 g tazg686*010l h #@0^++ 10 68.0 6.0 60 72 10 12 12 0.200 g tazh107*010c h #@0^++ 10 100.0 10.0 100 120 10 12 12 0.9 h tazh107*010l h #@0^++ 10 100.0 10.0 100 120 10 12 12 0.100 h tazh157*010c h #@0^++ 10 150.0 15.0 150 180 10 12 12 0.9 h tazh157*010l h #@0^++ 10 150.0 15.0 150 180 10 12 12 0.100 h tazv337*010l h #@0^++ 10 330.0 33.0 330 396 12 14 14 0.060 v taza684*015c h #@0^++ cwr09h^684*@+ h 15 0.68 1.0 10 12 6 8 8 12.0 a taza105*015c h #@0^++ 15 1.0 1.0 10 12 6 8 8 15.0 a tazb155*015c h #@0^++ cwr09h^155*@+ h 15 1.5 1.0 10 12 6 8 8 8.0 b tazb335*015c h #@0^++ 15 3.3 1.0 10 12 6 8 8 9.0 b tazd335*015c h #@0^++ cwr09h^335*@+ h 15 3.3 1.0 10 12 6 8 8 5.0 d tazd475*015c h #@0^++ 15 4.7 1.0 10 12 6 8 8 6.0 d taze475*015c h #@0^++ cwr09h^475*@+ h 15 4.7 1.0 10 12 6 8 8 4.0 e taze106*015c h #@0^++ 15 10.0 2.0 20 24 6 8 8 4.0 e tazf106*015c h #@0^++ cwr09h^106*@+ h 15 10.0 2.0 20 24 6 8 8 2.5 f tazf226*015c h #@0^++ 15 22.0 3.0 30 36 8 10 10 3.0 f tazg226*015c h #@0^++ cwr09h^226*@+ h 15 22.0 4.0 40 48 6 8 8 1.1 g tazh336*015c h #@0^++ cwr09h^336*@+ h 15 33.0 5.0 50 60 8 8 10 0.9 h tazh686*015c h #@0^++ 15 68.0 10.0 100 120 8 10 12 0.9 h tazh686*015l h #@0^++ 15 68.0 10.0 100 120 8 10 12 0.150 h tazh107*015c h #@0^++ 15 100.0 15.0 150 180 10 12 12 0.9 h tazh107*015l h #@0^++ 15 100.0 15.0 150 180 10 12 12 0.125 h tazv157*015l h #@0^++ 15 150.0 23.0 230 276 8 10 12 0.075 v tazv227*015l h #@0^++ 15 220.0 33.0 330 396 10 12 14 0.075 v part number designations surface mount military cwr09 - mil-prf-55365/4 and taz cots-plus ^ = termination finish: 1 # = inspection level: * = tolerance: @ = failure rate level: + = surge option: h = packaging: for taz p/n: s = std. conformance m = 20% weibull: b = 0.1%/1000 hrs. for taz p/n: for taz p/n: 9 = gold plated l = optional group a k = 10% (90% c = 0.01%/1000 hrs. 00 = none b = bulk 8 = hot solder dipped for cwr p/n: j = 5% (special conf.) 23 = 10 cycles, +25c r = 7" t&r 0 = solder fused m = military order only) comm: z = non er 24 = 10 cycles, s = 13" t&r for cwr p/n: conformance per -55c & +85c for cwr p/n: b = gold plated mil-prf-55365 for cwr p/n: bulk = standard c = hot solder dipped a = 10 cycles, +25c \tr = 7" t&r k = solder fused b = 10 cycles, \tr13 = 13" t&r -55c & +85c \w = waffle following the voltage code, c designates standard, l designates low esr ratings (1) v case size is only available as solder fused
24 surface mount military cwr09 - mil-prf-55365/4 and taz cots-plus dc leakage (max) dissipation factor (max) qpl part number dc rated cap esr (max) case avx part number (for reference only) voltage (nom) +25c +85c +125c +25c +85/125c -55c 100 khz size (85c) f (a) (a) (a) (%) (%) (%) +25c (volts) (ohms) taza474*020c h #@0^++ cwr09j^474*@+ h 20 0.47 1.0 10 12 6 8 8 14.0 a taza684*020c h #@0^++ 20 0.68 1.0 10 12 6 8 8 15.0 a tazb684*020c h #@0^++ cwr09j^684*@+ h 20 0.68 1.0 10 12 6 8 8 10.0 b tazb105*020c h #@0^++ cwr09j^105*@+ h 20 1.0 1.0 10 12 6 8 8 12.0 b tazb225*020c h #@0^++ 20 2.2 1.0 10 12 6 8 8 9.0 b tazd225*020c h #@0^++ cwr09j^225*@+ h 20 2.2 1.0 10 12 6 8 8 5.0 d tazd335*020c h #@0^++ 20 3.3 1.0 10 12 6 8 8 6.0 d taze335*020c h #@0^++ cwr09j^335*@+ h 20 3.3 1.0 10 12 6 8 8 4.0 e taze475*020c h #@0^++ 20 4.7 1.0 10 12 6 8 8 6.0 e taze685*020c h #@0^++ 20 6.8 2.0 20 24 6 8 8 5.0 e tazf685*020c h #@0^++ cwr09j^685*@+ h 20 6.8 2.0 20 24 6 8 8 2.4 f tazf156*020c h #@0^++ 20 15.0 3.0 30 36 6 8 8 3.0 f tazg156*020c h #@0^++ cwr09j^156*@+ h 20 15.0 3.0 30 36 6 8 8 1.1 g tazg226*020c h #@0^++ 20 22.0 4.0 40 48 6 8 8 2.5 g tazg226*020l h #@0^++ 20 22.0 4.0 40 48 6 8 8 0.500 g tazh226*020c h #@0^++ cwr09j^226*@+ h 20 22.0 4.0 40 48 6 8 8 0.9 h tazh476*020c h #@0^++ 20 47.0 10.0 100 120 8 10 10 0.9 h tazh476*020l h #@0^++ 20 47.0 10.0 100 120 8 10 10 0.250 h tazv107*020l h #@0^++ 20 100.0 20.0 200 240 10 12 14 0.095 v taza334*025c h #@0^++ cwr09k^334*@+ h 25 0.33 1.0 10 12 6 8 8 15.0 a tazb684*025c h #@0^++ cwr09k^684*@+ h 25 0.68 1.0 10 12 6 8 8 7.5 b tazb105*025c h #@0^++ 25 1.0 1.0 10 12 6 8 8 10.0 b tazd155*025c h #@0^++ cwr09k^155*@+ h 25 1.5 1.0 10 12 6 8 8 6.5 d tazd225*025c h #@0^++ 25 2.2 1.0 10 12 6 8 8 6.0 d taze225*025c h #@0^++ cwr09k^225*@+ h 25 2.2 1.0 10 12 6 8 8 3.5 e taze335*025c h #@0^++ 25 3.3 1.0 10 12 6 8 8 4.0 e tazf475*025c h #@0^++ cwr09k^475*@+ h 25 4.7 2.0 20 24 6 8 8 2.5 f tazf685*025c h #@0^++ 25 6.8 2.0 20 24 6 8 8 3.0 f tazg685*025c h #@0^++ cwr09k^685*@+ h 25 6.8 2.0 20 24 6 8 8 1.2 g tazg106*025c h #@0^++ cwr09k^106*@+ h 25 10.0 3.0 30 36 6 8 8 1.4 g tazh156*025c h #@0^++ cwr09k^156*@+ h 25 15.0 4.0 40 48 6 8 8 1.0 h tazh226*025c h #@0^++ 25 22.0 6.0 60 72 6 8 8 0.9 h tazh226*025l h #@0^++ 25 22.0 6.0 60 72 6 8 8 0.200 h tazv686*025l h #@0^++ 25 68.0 17.0 170 204 10 12 14 0.095 v part number designations ^ = termination finish: 1 # = inspection level: * = tolerance: @ = failure rate level: + = surge option: h = packaging: for taz p/n: s = std. conformance m = 20% weibull: b = 0.1%/1000 hrs. for taz p/n: for taz p/n: 9 = gold plated l = optional group a k = 10% (90% c = 0.01%/1000 hrs. 00 = none b = bulk 8 = hot solder dipped for cwr p/n: j = 5% (special conf.) 23 = 10 cycles, +25c r = 7" t&r 0 = solder fused m = military order only) comm: z = non er 24 = 10 cycles, s = 13" t&r for cwr p/n: conformance per -55c & +85c for cwr p/n: b = gold plated mil-prf-55365 for cwr p/n: bulk = standard c = hot solder dipped a = 10 cycles, +25c \tr = 7" t&r k = solder fused b = 10 cycles, \tr13 = 13" t&r -55c & +85c \w = waffle following the voltage code, c designates standard, l designates low esr ratings (1) v case size is only available as solder fused.
25 surface mount military cwr09 - mil-prf-55365/4 and taz cots-plus dc leakage (max) dissipation factor (max) qpl part number dc rated cap esr (max) case avx part number (for reference only) voltage (nom) +25c +85c +125c +25c +85/125c -55c 100 khz size (85c) f (a) (a) (a) (%) (%) (%) +25c (volts) (ohms) taza224*035c h #@0^++ cwr09m^224*@+ h 35 0.22 1.0 10 12 6 8 8 18.0 a tazb474*035c h #@0^++ cwr09m^474*@+ h 35 0.47 1.0 10 12 6 8 8 10.0 b tazd105*035c h #@0^++ cwr09m^105*@+ h 35 1.0 1.0 10 12 6 8 8 6.5 d taze155*035c h #@0^++ cwr09m^155*@+ h 35 1.5 1.0 10 12 6 8 8 4.5 e tazf335*035c h #@0^++ cwr09m^335*@+ h 35 3.3 1.0 10 12 6 8 8 2.5 f tazg475*035c h #@0^++ cwr09m^475*@+ h 35 4.7 2.0 20 24 6 8 8 1.5 g tazh685*035c h #@0^++ cwr09m^685*@+ h 35 6.8 3.0 30 36 6 8 8 1.3 h tazh106*035c h #@0^++ 35 10.0 4.0 40 48 8 10 10 0.9 h tazh106*035l h #@0^++ 35 10.0 4.0 40 48 8 10 10 0.300 h taza104*050c h #@0^++ cwr09n^104*@+ h 50 0.10 1.0 10 12 6 8 8 22.0 a taza154*050c h #@0^++ cwr09n^154*@+ h 50 0.15 1.0 10 12 6 8 8 17.0 a tazb224*050c h #@0^++ cwr09n^224*@+ h 50 0.22 1.0 10 12 6 8 8 14.0 b tazb334*050c h #@0^++ cwr09n^334*@+ h 50 0.33 1.0 10 12 6 8 8 12.0 b tazd684*050c h #@0^++ cwr09n^684*@+ h 50 0.68 1.0 10 12 6 8 8 7.0 d taze105*050c h #@0^++ cwr09n^105*@+ h 50 1.0 1.0 10 12 6 8 8 6.0 e tazf155*050c h #@0^++ cwr09n^155*@+ h 50 1.5 1.0 10 12 6 8 8 4.0 f tazf225*050c h #@0^++ cwr09n^225*@+ h 50 2.2 2.0 20 24 6 8 8 2.5 f tazg335*050c h #@0^++ cwr09n^335*@+ h 50 3.3 2.0 20 24 6 8 8 2.0 g tazh475*050c h #@0^++ cwr09n^475*@+ h 50 4.7 3.0 30 36 6 8 8 1.5 h part number designations ^ = termination finish: 1 # = inspection level: * = tolerance: @ = failure rate level: + = surge option: h = packaging: for taz p/n: s = std. conformance m = 20% weibull: b = 0.1%/1000 hrs. for taz p/n: for taz p/n: 9 = gold plated l = optional group a k = 10% (90% c = 0.01%/1000 hrs. 00 = none b = bulk 8 = hot solder dipped for cwr p/n: j = 5% (special conf.) 23 = 10 cycles, +25c r = 7" t&r 0 = solder fused m = military order only) comm: z = non er 24 = 10 cycles, s = 13" t&r for cwr p/n: conformance per -55c & +85c for cwr p/n: b = gold plated mil-prf-55365 for cwr p/n: bulk = standard c = hot solder dipped a = 10 cycles, +25c \tr = 7" t&r k = solder fused b = 10 cycles, \tr13 = 13" t&r -55c & +85c \w = waffle following the voltage code, c designates standard, l designates low esr ratings (1) v case size is only available as solder fused.
26 cwr09 series mil-c-55365/4 mil-c-55365/4 case rated capacitance dc leakage (max.) dissipation factor (max.) max. esr part size w voltage (nom.) 100 khz number (85c) (f) +25c +85c +125c +25c +85/125c -55c +25c (see note) (volts) (a) (a) (a) (%) (%) (%) style cwr09 (ohms) cwr09c*225?@ nh a 4 2.2 1.0 10 12 6 8 8 8.0 cwr09c*475?@ nh b 4 4.7 1.0 10 12 6 8 8 8.0 cwr09c*685?@ nh c 4 6.8 1.0 10 12 6 8 8 5.5 cwr09c*106?@ nh d 4 10.0 1.0 10 12 8 8 10 4.0 cwr09c*156?@ nh e 4 15.0 1.0 10 12 8 10 12 3.5 cwr09c*336?@ nh f 4 33.0 2.0 20 24 8 10 12 2.2 cwr09c*686?@ nh g 4 68.0 3.0 30 36 10 12 12 1.1 cwr09c*107?@ nh h 4 100.0 4.0 40 48 10 12 12 0.9 cwr09d*155?@ nh a 6 1.5 1.0 10 12 6 8 8 8.0 cwr09d*335?@ nh b 6 3.3 1.0 10 12 6 8 8 8.0 cwr09d*475?@ nh c 6 4.7 1.0 10 12 6 8 8 5.5 cwr09d*685?@ nh d 6 6.8 1.0 10 12 6 8 8 4.5 cwr09d*106?@ nh e 6 10.0 1.0 10 12 8 10 12 3.5 cwr09d*226?@ nh f 6 22.0 2.0 20 24 8 10 12 2.2 cwr09d*476?@ nh g 6 47.0 3.0 30 36 10 12 12 1.1 cwr09d*686?@ nh h 6 68.0 4.0 40 48 10 12 12 0.9 cwr09f*105?@ nh a 10 1.0 1.0 10 12 6 8 8 10.0 cwr09f*225?@ nh b 10 2.2 1.0 10 12 6 8 8 8.0 cwr09f*335?@ nh c 10 3.3 1.0 10 12 6 8 8 5.5 cwr09f*475?@ nh d 10 4.7 1.0 10 12 6 8 8 4.5 cwr09f*685?@ nh e 10 6.8 1.0 10 12 6 8 8 3.5 cwr09f*156?@ nh f 10 15.0 2.0 20 24 8 8 10 2.5 cwr09f*336?@ nh g 10 33.0 3.0 30 36 10 12 12 1.1 cwr09f*476?@ nh h 10 47.0 5.0 50 60 10 12 12 0.9 cwr09h*684?@ nh a 15 0.68 1.0 10 12 6 8 8 12.0 cwr09h*155?@ nh b 15 1.5 1.0 10 12 6 8 8 8.0 cwr09h*225?@ nh c 15 2.2 1.0 10 12 6 8 8 5.5 cwr09h*335?@ nh d 15 3.3 1.0 10 12 6 8 8 5.0 cwr09h*475?@ nh e 15 4.7 1.0 10 12 6 8 8 4.0 cwr09h*106?@ nh f 15 10.0 2.0 20 24 6 8 8 2.5 cwr09h*226?@ nh g 15 22.0 4.0 40 48 8 8 10 1.1 cwr09h*336?@ nh h 15 33.0 5.0 50 60 8 8 10 0.9 cwr09j*474?@ nh a 20 0.47 1.0 10 12 6 8 8 14.0 cwr09j*684?@ nh b 20 0.68 1.0 10 12 6 8 8 10.0 cwr09j*105?@ nh b 20 1.0 1.0 10 12 6 8 8 12.0 cwr09j*155?@ nh c 20 1.5 1.0 10 12 6 8 8 6.0 cwr09j*225?@ nh d 20 2.2 1.0 10 12 6 8 8 5.0 cwr09j*335?@ nh e 20 3.3 1.0 10 12 6 8 8 4.0 cwr09j*685?@ nh f 20 6.8 2.0 20 24 6 8 8 2.4 cwr09j*156?@ nh g 20 15.0 3.0 30 36 6 8 8 1.1 cwr09j*226?@ nh h 20 22.0 4.0 40 48 6 8 8 0.9 electrical ratings for cwr09 capacitors * = termination finish b = gold plated c = hot solder dipped k = solder fused ? = tolerance code j = 5% k = 10% m = 20% @ = failure rate level exponential: m = 1.0% per 1000 hours p = 0.1% per 1000 hours r = 0.01% per 1000 hours s = 0.001% per 1000 hours weibull: b = 0.1% per 1000 hours c = 0.01% per 1000 hours n = optional surge current a = 10 cycles at 25c b = 10 cycles at -55c and +85c h = packaging bulk standard \tr=7" tape & reel \tr13=13" tape & reel \w=waffle pack w the c case has limited availability. where possible d case should be substituted.
27 cwr09 series mil-c-55365/4 * = termination finish b = gold plated c = hot solder dipped k = solder fused ? = tolerance code j = 5% k = 10% m = 20% @ = failure rate level exponential: m = 1.0% per 1000 hours p = 0.1% per 1000 hours r = 0.01% per 1000 hours s = 0.001% per 1000 hours weibull: b = 0.1% per 1000 hours c = 0.01% per 1000 hours n = optional surge current a = 10 cycles at 25c b = 10 cycles at -55c and +85c h = packaging bulk standard \tr=7" tape & reel \tr13=13" tape & reel \w=waffle pack electrical ratings for cwr09 capacitors mil-c-55365/4 case rated capacitance dc leakage (max.) dissipation factor (max.) max. esr part size w voltage (nom.) 100 khz number (85c) (f) +25c +85c +125c +25c +85/125c -55c +25c (see note) (volts) (a) (a) (a) (%) (%) (%) style cwr09 (ohms) cwr09k*334?@ nh a 25 0.33 1.0 10 12 6 8 8 15.0 cwr09k*684?@ nh b 25 0.68 1.0 10 12 6 8 8 7.5 cwr09k*105?@ nh c 25 1.0 1.0 10 12 6 8 8 6.5 cwr09k*155?@ nh d 25 1.5 1.0 10 12 6 8 8 6.5 cwr09k*225?@ nh e 25 2.2 1.0 10 12 6 8 8 3.5 cwr09k*475?@ nh f 25 4.7 2.0 20 24 6 8 8 2.5 cwr09k*685?@ nh g 25 6.8 2.0 20 24 6 8 8 1.2 cwr09k*106?@ nh g 25 10.0 3.0 30 36 6 8 8 1.4 cwr09k*156?@ nh h 25 15.0 4.0 40 48 6 8 8 1.0 cwr09m*224?@ nh a 35 0.22 1.0 10 12 6 8 8 18.0 cwr09m*474?@ nh b 35 0.47 1.0 10 12 6 8 8 10.0 cwr09m*684?@ nh c 35 0.68 1.0 10 12 6 8 8 8.0 cwr09m*105?@ nh d 35 1.0 1.0 10 12 6 8 8 6.5 cwr09m*155?@ nh e 35 1.5 1.0 10 12 6 8 8 4.5 cwr09m*335?@ nh f 35 3.3 1.0 10 12 6 8 8 2.5 cwr09m*475?@ nh g 35 4.7 2.0 20 24 6 8 8 1.5 cwr09m*685?@ nh h 35 6.8 3.0 30 36 6 8 8 1.3 cwr09n*104?@ nh a 50 0.10 1.0 10 12 6 8 8 22.0 cwr09n*154?@ nh a 50 0.15 1.0 10 12 6 8 8 17.0 cwr09n*224?@ nh b 50 0.22 1.0 10 12 6 8 8 14.0 cwr09n*334?@ nh b 50 0.33 1.0 10 12 6 8 8 12.0 cwr09n*474?@ nh c 50 0.47 1.0 10 12 6 8 8 8.0 cwr09n*684?@ nh d 50 0.68 1.0 10 12 6 8 8 7.0 cwr09n*105?@ nh e 50 1.0 1.0 10 12 6 8 8 6.0 cwr09n*155?@ nh f 50 1.5 1.0 10 12 6 8 8 4.0 cwr09n*225?@ nh f 50 2.2 2.0 20 24 6 8 8 2.5 cwr09n*335?@ nh g 50 3.3 2.0 20 24 6 8 8 2.0 cwr09n*475?@ nh h 50 4.7 3.0 30 36 6 8 8 1.5 note: to complete the mil-c-55365/4 part number, additional information must be added: contact your local avx sales office for latest qualification status. w the c case has limited availability. where possible d case should be substituted.
|
